The new nut concept for long travel distances, compressive force transmission, and high dynamics
For long travel distances, the conventional ball screw with a rotating screw shaft reaches its limits sooner than its force transmission capability would suggest. The limiting factor is the critical speed: above a certain combination of screw shaft length and speed, the rotating screw shaft begins to oscillate. This effect impairs the positioning accuracy and service life of the system and limits the achievable travel speed.
Kammerer has developed a ball screw with a driven nut that circumvents this limit by design.
The principle: the nut rotates, not the screw shaft
In the driven nut concept, the kinematics are reversed: the screw shaft is stationary, while the driven nut rotates and, through its own rotation, moves relative to the screw shaft. This produces the linear motion.
This has a direct physical consequence: a stationary screw shaft does not reach a critical speed. Long travel distances and high speeds can therefore be achieved without the screw shaft length becoming the limiting parameter. At the same time, this principle allows for a compact design: between the force input and the force output, transmission takes place exclusively via the rolling elements typical of ball screws, namely the balls, which ensure the high efficiency of the drive.
Other design limits still remain. Under compressive load, the stationary screw shaft must still be designed to withstand buckling. Particularly in presses, bending machines, or with long travel distances, this can be the decisive parameter. In addition, the maximum recommended speed of the bearings of the rotating nut limits the maximum possible speed. These factors are taken into account when designing each axis.
Two installation variants of the driven nut
In both cases, the nut is set in rotation. The difference lies in which component is stationary.
In the classic application, for example in machine tools, the screw shaft is rigidly clamped at both ends. The nut, together with its bearing housing, travels along the screw shaft and moves the attached load axially, such as a traveling column, even over very long travel distances.
The situation is different when the driven nut is used as an analogy to a pressure cylinder: the bearing housing of the nut is mounted in a fixed position. The rotating nut moves the torque-supported screw shaft axially and extends it out of the housing, comparable to the piston rod of a cylinder. In this way, an electromechanical alternative to hydraulic and pneumatic cylinders can be built, for example in presses or bending machines.
|
Compressive load applications |
Classic application |
|
|
Stationary |
Bearing housing of the nut |
Screw shaft, clamped at both ends |
|
Rotation |
Nut |
Nut |
|
Translation |
Spindle |
Nut with bearing housing and load |
|
Typical use |
Press, bending machines |
Machine tools with long travel distances |
Applications: Machine tools, presses, and bending machines
In both cases, the nut is set in rotation. The difference lies in which component is stationary.
Machine tools with long to very long travel distances are the primary field of application. The screw shaft hardly builds up any noticeable oscillation, and the achievable travel speed is no longer directly limited by the critical speed. This allows machine configurations with long linear axes that would be difficult to manage from a design perspective with conventional screw drives.
In presses, the ball screw with a driven nut enables direct controllability and positioning capability. This makes recording force-displacement curves easier than with hydraulic systems, for example. The force is defined and controllable at all times, and process parameters can be recorded and documented reproducibly.
In bending machines, the concept has already been validated for specific applications: the ball screws with a driven nut were designed for high compressive forces and for use without an external guide system, with operation functionally comparable to that of a hydraulic cylinder.
Where ball screws replace pneumatic or hydraulic cylinders, the use of compressed air or hydraulic fluid is eliminated. This fundamentally reduces operating costs, minimizes maintenance and disposal effort, and eliminates the risk of leakage, which is particularly relevant in hygienically sensitive environments or when handling hazardous substances.
Lubrication: a single connection
A practical advantage of the nut concept that is essential in daily operation is the integration of a single lubrication access point into the design. The ball bearing and the ball nut must be reliably supplied with lubricant. Until now, two separate connections were often provided for this purpose, each requiring its own lubricant quantities and intervals.
Kammerer’s new concept functionally combines the ball bearing and the ball nut in a single assembly. Via a single lubrication access point, both components are dynamically supplied with lubricant as soon as the nut is set in rotation. This ensures the basic prerequisite for high positioning accuracy and longevity. It simplifies integration into machine-side lubrication systems, reduces the number of maintenance points, and lowers the effort in daily operation.
Vertical integration: everything from a single source
The Kammerer product range for the driven nut is designed for maximum vertical integration. All components relevant to performance and service life, namely the screw shaft, nut, and bearing housing, are conceived, engineered, designed, and manufactured in-house. Purchased parts are limited to standard parts. This means: no stiffness losses due to component interfaces, reduced dependence on suppliers, and direct feedback between design and production when application-specific adaptations are required.
Classification
The nut concept is an independent design approach that circumvents a well-known physical limit, the critical speed of the rotating screw shaft, by reversing the kinematics, without disregarding the other design limits. For design engineers who develop linear axes with long travel distances, high speeds, or high compressive forces, it expands the design scope in an area where the conventional screw drive reaches its system limits.